Welcome to the Staffs-VW Forum


Staffordshire's Biggest Volkswagen, Audi, Skoda & SEAT Forum; find


  •  » Technical Advice for Problem solving
  •  » Advice about Insurance, modifications and Tuning
  •  » Discounts for Cleaning and Detailing with Advice Forums
  •  » Network with Fellow VAG enthusiasts
  •  » Advice on regular maintenance for your VW

VW Forum for Staffordshire, Cheshire, Derbyshire & West Midlands


For Site advertising please contact us via HERE


REGISTER HERE FOR FREE


p.s.: Registered members will not see this ad

Results 1 to 2 of 2

Thread: 15 x 4.5 Fuchs Chrome Alloy Wheels 5x130 PCD ET45 (Each)

  1. #1

    Post 15 x 4.5 Fuchs Chrome Alloy Wheels 5x130 PCD ET45 (Each)

    15 x 4.5 Fuchs Chrome Alloy Wheels 5x130 PCD ET45 (Each)

    Aircooled VW Premium Steel and Alloy Wheels

    Fuch Chrome Alloy Wheels 15"
    Specs Below:
    - Wheel Diameter: 15"
    - Wheel Width (J Value): 4.5"
    - ET (Offset): ET45
    - PCD: 5x130
    - Centre Cap: Included
    - Mounting Hardware: Included
    - Quantity: Listing for one wheel, (Each)
    Wheel Terminology, PCD, Offset, J & ET Explained

    What is ET?
    Often times you will hear people talk about ET on a wheel, it may seem strange that ET is actually the term for offset despite the abbreviation not resembling the meaning at all the reason for this is because it is derived from the german word 'Einpresstiefe'.
    So next is understanding where to measure to and from. ET is always measured from the imaginary centre line of the wheel as you can see to the left.
    Nearly all wheels you will find will be positive offset, their is a number of reasons linking to better balance of rotating mass, caliper clearance and reducing the overall width of the vehicle, however there are some exceptions.
    So for the measuring process for an ET45 Offset you would take your imaginary centre line and measure 45mm toward the face of the wheel and this would be the position where the hub will mount to the wheel.


    What is PCD?
    PCD, or Pitch Circle Diameter is the diameter of which wheel studs are apart through centre of the hub. PCD fitments are a measurement showing the number of studs/bolts followed by the distance they are apart. The distance is usually shown in millimetres. So a PCD of 4x130 would mean that there are 4 studs or bolt holes evenly spaced around a circle with a diameter of 130mm.
    What is 'J' Width?
    The letter that typically denotes the distance between the rim edges, not including the rolled edge. The terminology refers to the sectional profile of the wheel, it just happens to be the point which most manufacturers use, probably because it is a relevant measurement for choosing tyre size and is a critical measurement far more than the lip itself which could vary massively from company to company.

    width figures are easily calculated with a tape measure, and can normally be found stamped in the wheel, in the cross-section on the left you can see the area highlighted in red to visually represent where this measurement is taken from.

    Product Code: 50010076
    OE Code:
    Any Questions, Please Contact Us Here




    More info...


  2. #2

    Re: 15 x 4.5 Fuchs Chrome Alloy Wheels 5x130 PCD ET45 (Each)

    Excellent post. Thank you very much!!


Similar Threads

  1. Replies: 1
    Last Post: 16-03-2017, 01:35 PM
  2. Replies: 0
    Last Post: 01-03-2017, 03:33 PM
  3. Replies: 0
    Last Post: 28-02-2017, 03:59 AM
  4. Replies: 0
    Last Post: 26-02-2017, 01:07 AM
  5. Replies: 0
    Last Post: 26-02-2017, 01:07 AM

Visitors found this page by searching for:

Nobody landed on this page from a search engine, yet!

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •